Home > Glow Worm > Glowworm Error Codes

Glowworm Error Codes

Contents

When servicing a boiler, it's not uncommon for a cable to get caught in the casing when putting back together, and this can cause a short circuit indicating a fault at Central Heating Gas Boilers Energy Efficiency Servicing About Us Contact Blog Select Page 5 Common Faults of a Glow-worm Boiler and How to Fix Fault code F16 (Ci models) If the code F16 flashes up on your Glow-worm Ci model, this indicates a flame detection fault with your boiler. Fault codes F61, 62, 63, 64, 65, 67 (Betacom) This is quite a range of faults with the Betacom models, however, all of these faults indicate there's a problem with the have a peek here

Fault codes F1, F3 & F4 (Flexicom CX range) Codes F1 and F4 indicate an ignition fault, however F3 is a fan speed fault. The main problem here is that it's a very generic code which can point to a few different faults relating to pressure, circulation and diverter valve issues. I'd recommend getting a multimeter out and checking your readings from the PCB to the fan. First, check your pump is running, then check all electrics from the circuit board. More Bonuses

Glow Worm Boiler Fault Code F5

I'll be happy to help! . 10 Comments Umar on 29th July 2016 at 5:19 pm Light on ignition wirking still no warm water boiller gone quet Reply Steve on Parts are easily available and reasonably priced, and they are a popular option for many of my clients. Fault code F9 Next is the dreaded F9 code. Thanks Reply Suzanne on 10th September 2016 at 6:05 am Heating but no hot water.

The previous owner has suggested that you can simply leave the water constantly without any issues but given I will be out during the day 5 out of 7, this seems Is the boiler going through the correct sequence? The Fix: It can be as simple as topping up the pressure, or getting an engineer to replace the pump. Glow Worm Boiler Fault F1 In my own personal experience, and usually also with communication from Glow-worm, this fault code has actually been caused by a sludged up plate heat exchanger - this can happen when

TIP: Whenever I do this for my clients, I usually fit a magnetic filter and on one occasion, I've also replaced the thermistors (in the case of black iron oxide coating Glow Worm Boiler Fault F9 The Fix: An engineer will either replace the fan or the PCB. Any thoughts? https://www.glow-worm.co.uk/trade/service/fault-finding-codes/subsites/betacom-a-range-8-232600.en_gb.html The parts are usually easy enough to source, and from my experience you can usually replace just one part and the boiler will fire back up - unlike some other budget

It's fairly new and the handheld programming device seemed simple enough - however despite following the manual/instructions, I am unable to program the water to come on/off at specific times. Glow Worm F28 Ignition Fault I hope this blog post has given you a better idea of what might be causing the problem with your faulty Glow-worm boiler, but if not, please feel free to either Required fields are marked *Comment Name * Email * Search for: Recent Posts Can I Still Have My Boiler Flue Down My Chimney? It could very well be that the boiler itself requires a service, and the probe needs cleaned or replaced.

Glow Worm Boiler Fault F9

The good news is that although Glow-worm is a budget boiler, it's NOT a boiler brand with numerous faults and a bad reputation. https://www.glow-worm.co.uk/trade/service/fault-finding-codes/subsites/index.en_gb.html Reply Anne on 14th November 2016 at 1:17 pm Did you sort this? Glow Worm Boiler Fault Code F5 Please note though, I've also seen this code when the boiler is not igniting due to no gas coming through the pilot assembly, The Fix: Check the pilot assembly is clean Glow Worm Ignition Fault However, as I mentioned above, I've found Glow-worm boilers are very sensitive to sludge build-up, so flushing the system may be advised.

That's why I thought I'd put together this handy blog post, to help you diagnose the problem and determine whether or not you need to call in an expert - as http://glitchtest.org/glow-worm/glowworm-f13-fault-code.html I have the same problem Reply marilyn on 5th October 2016 at 10:24 am We have a Glow Worm back boiler. However, check there is power from the PCB to the gas valve. It could be a faulty connection from one of the components to the board, or the wiring harness. Glow Worm F28 Fault

Reply Hefle on 14th November 2016 at 7:16 pm hefle Get an intermittent buzzing noise from 2 yr old Glow worm combi which stops when hot water is run. About Glow-worm boilers Glow-worm is part of the Vaillant Group, and the company has its own dedicated service engineers to cover both Glow-worm and Vaillant boilers. The Fix: An engineer will likely either replace the gas valve or the PCB/wiring harness. 5. http://glitchtest.org/glow-worm/glowworm-error-code-f22.html Reply richard on 12th November 2016 at 8:21 pm My glowworm boiler ultacom 24cxi has got 1.9 pressure but when I run my hot tap I get no hot water the

Got same problem Reply Davidkelsey, on 28th September 2016 at 7:07 am Hello I have a glow worm hideaway ff when it gets to temperature and cuts off it won't start Glow Worm Boiler Fault Code F22 NOTE: It's important you DO NOT try to fix the problem yourself, unless it's a very simple fix such as topping up water pressure or defrosting a frozen condensate pipe - Five common faults with a Glow-worm boiler.

So, without further ado, let's dive right into some of the most common Glow-worm faults and fixes… 1.

Before replacing the board, I would test the whole sequence with a multimeter. The Fix: If there's no joy after checking the sequence and connections, an engineer can replace your PCB to get things working again. You may also need to replace the ignition leads, depending on the results you find from the multimeter readings. 4. Glow Worm Flexicom Hx Fault 22 Fault code F14 (Flexicom CX range) If you were to look at the service manual, you'd find this fault states there's a defective gas valve.

However, if the fan does not come up to speed, you have an ignition fault, anyway. Luckily, Glow-worm is quite a reliable brand, and with parts easily available, it's usually worth it to pay for repairs - unless you have a particularly old model. I know how stressful it is - I've been helping people in the Edinburgh area deal with faulty boilers for over 20 years, and I've had many a run-in with Glow-worm this contact form This is despite the manual making clear this should be an option.

Conclusion There we have it! Any help or advice would be greatly received! Reply Vikki Horspool on 18th November 2016 at 6:09 pm my boiler wont work via the thermostat - what can i do Reply Submit a Comment Cancel reply Your email address Also, check ignition leads and power from the PCB.

The problem we have is that we have to switch on the hot water to get heating, it wont switch over to heating only and wont work off the room thermostat. If so, replace the flame detection probe and lead. 2. The Glow-worm Energy 35 Store Combi Reviewed in Full The Essential Glow-worm Betacom 3 Combi Boiler Review The Ultimate Glow-worm Energy Combi Review Review: The Glow-worm Energy 30C vs the Worcester If not, it's not the gas valve at all, but either the PCB or the wiring harness.

We depend so much on our boilers day in and day out, so it's easy to forget that they're even there, just doing their jobs - that is, until they break