Home > Error Code > Genmega Error Codes

Genmega Error Codes

Contents

One or two instances of this error does not usually indicate a defective part. Contact host processor D00A1 FS omitted (after available balance) Verify all programming. D00A4 ETX is in wrong place. C0049 Dispense request of “0” notes Check setup of CDU in Operator Menu, dispenser may need reprogramming. http://glitchtest.org/error-code/getlasterror-codes.html

Please try the request again. Contact host processor. ATM Error Codes Fast CashError Codes HantleError Codes HyosungError Codes Genmega Error Codes Error Codes WRG GenesisError Codes HomeAbout usProducts/ServicesATMsParts & PaperServiceProcessingFormsError CodesContact UsEvents ©1997-2016CopyrightATMCentral. Also check that black and white, 2 wire connector is properly connected at rear of main board. http://www.accessatm.com/service/atm-error-codes/genmega-error-codes/

D0111 Error Code

Check cables between Printer and Mainboard. Verify that version of ATM Software matches host processor. Dispenser may require service. Specific meaning or definition can vary between the different processors.

Axxx4 Receipt paper is empty. D0056 No card record found Code reported by host processor (Shazam). Check for jammed notes or blocked sensors. D2516 Atm Error C00FF Sensor blocked None CANCE User canceled transaction at surcharge This is not an error, but rather a statistic to notify how many users respond "no" to the surcharge notification.

Make sure the ATM is turned on, the phone line fits securely on both ends, and not shared with a voice phone nor experiences static. Genmega Error D2511 All Rights Reserved. Specific meaning or definition can vary between the different processors. If the error persists, the vault assembly may need to be removed to inspect / access the cash tray sensors.

In line filter may help this. Genmega G2500 Manual Verify that version of ATM Software matches host processor. Contact host processor. Other than upgrading the cash tray or using a sign to warn customers, you can loosen the screws that hold the dispenser and slide it back.

Genmega Error D2511

C0028 Count sensors not cleared Check dispenser for jammed bills and reinitialize the machine. http://www.atmcentral.com/error-codes.html D00A6 FS omitted (after total non cash dispense amount in day close). D0111 Error Code Make sure you only are using 21# paper. D2516 Error Code Check the quality of the notes and condition of the pick rollers.

Contact host processor. this contact form Remove any jammed bills from the dispenser, if no bills are present try using compressed air to clean the dispenser (a sensor may be blocked by dust). D0039 No credit account Code reported by host processor. All Rights Reserved ATM Central6468 5th Avenue S St. Genmega Tech Support

If they are broken the cassette will not stay in the dispenser. 20002 Low Cash Low cash warning sensor on dispenser is open. Reinitialize CDU C0083 Stacker sensor failure Check all wiring connections to CDU mainboard. Check transaction with the processor. have a peek here C0036 Detected notes in path before initializing One or more sensors in the dispenser detected a blockage prior to initializing.

NOTE: Do not use metal objects to clear the jam. Hantle 1700w Error Codes Set refresh timer – (Customer Setup) F0005 No Advertisement text when advertisement is enabled. Contact host processor.

If no bills are present try using compressed air to clean the dispenser (a sensor may be blocked by dust).

Code reported by host processor. Contact your ISO or processor if you encounter an excessive amount of these errors, or you cannot complete a test transaction because of this error. Check dispenser and cassette for jammed bills. Genmega Atm Hack Verify that version of Mini-Bank Software matches host processor.

Inspect the cassette detection microswitch. The CDU belts or the Cassette rollers may need to be cleaned (rubbing alcohol). If this error persists, the printer will require service. 20215 CDU detects bills prior to dispensing This means that while the ATM was initializing it detected a blocked sensor in the http://glitchtest.org/error-code/gle-error-codes.html C0062 3rd cassette inlet sensor not cleared Check for notes where the 3rd cassette engages the dispenser.

Verify that version of Mini-Bank Software matches host processor. D00A0 FS omitted (after account balance). Check the front of the CDU and the cash tray for blockage. Check the condition of the white plastic cassette retaining clips in the dispenser.

Network denial code. Loose belts can slip off rollers and block sensors. 90001 Error during card swipe This error occurs when customer attempts to swipe their card and are unsuccessful. Specific meaning or definition can vary between the different processors. Contact your ISO or processor if you encounter an excessive amount of these errors, or you cannot complete a test transaction because of this error.

C0047 Feed error This error occurs when the dispenser attempts to pull a bill from the cassette and is unsucessfull before the dispenser times out. C00C7 CS12 Sensor blocked MB2100T - The CS12 sensor, which is located at the upper part of the cash tray was blocked while the machine was either dispensing or initializing. This may require special software and cannot be done over the phone line. C0052 Detected notes in path after dispense Remove any notes from path, verify amount of dispensed notes.